Seal-It® 646 EPDM Spraybond DCM is a very high-quality, extremely strong SBR-Rubber- based contact adhesive. Suitable for bonding both American and European EPDM rubber to itself and various surfaces, including MDF, chipboard, plywood, OSB and other wood panel materials. Also suitable for bonding insulation board, concrete, masonry, brick, most metals and their respective bonding.
Seal-it® 646 EPDM Spraybond DCM
- Extremely fast drying, sprayable 1K contact adhesive
- Specifically for bonding EPDM
- Rapid strength build-up and high final strength
Seal-It® 646 EPDM Spraybond DCM is a very high-quality, extremely strong SBR-Rubber- based contact adhesive. Suitable for bonding both American and European EPDM rubber to itself and various surfaces, including MDF, chipboard, plywood, OSB and other wood panel materials. Also suitable for bonding insulation board, concrete, masonry, brick, most metals and their respective bonding.
Applications
- Very high quality contact adhesive for bonding both American and European EPDM on most surfaces such as concrete, metal, hard plastics, HPL and wood (not suitable on vinyl, EPS and polystyrene).
- Due to the high solids and rubber content, this adhesive is extremely strong and safe to use on roofs of garden houses, dormers and large industrial roofs.
Properties
- Dries extremely quickly
- For bonding large and small EPDM membranes.
- Forms a durable adhesion between EPDM and all kinds of surfaces.
- Adjustable spray pattern
- Easy to apply using our SEAL-IT® 580 SPRAYGUN
- Temperature resistance from -30°C to 90°C
- Ready-to-use, 1-component.
- Excellent UV, weather, water, moisture and aging resistant.
Application conditions
- Application temperature (environment and substrate) between + 10°C and + 30°C.
- Attach the hose securely to the spray gun. Attach the other end of the hose to the canister. Make sure the connections are tight. Slowly open the valve completely on the canister, checking for leaks during this process. Release the trigger of the spray gun to start spraying.
- Before use, check compatibility by spraying some adhesive on the substrate. This product could be harmful some substrates.
- Shake and / or mix SEAL-IT® 646 EPDM SPRAYBOND DCM well before use.
- Before applying SEAL-IT® 646 EPDM SPRAYBOND DCM, apply a brush to the substrates to remove loose components.
- Bonding surfaces and other surfaces must be dry, clean, uncontaminated, grease-free, dust-free, compatible and stable.
- Spray SEAL-IT® 646 EPDM SPRAYBOND DCM at a distance of about 10-20 cm at a 90 degree angle to the surface and apply a uniform, even layer of adhesive to obtain 80% to 100% coverage of the surface. If necessary, spray another layer of adhesive where more adhesive appears to be needed.
- Spray both substrates, one surface vertically and the other surface horizontally.
- Let SEAL-IT® 646 EPDM SPRAYBOND DCM air for 1 to 3 minutes until no adhesive sticks to your finger.
- Bond surfaces together and compress with sufficient pressure. A roller is recommended to apply even pressure to achieve maximum strength. Allow the adhesive to fully cure for 24 hours.
- If the nozzle clogs, unscrew the nozzle from the gun and clean it with a solvent such as thinner or acetone. Do not use a pin on the nozzle opening.
Assortment
| Colour | 12 x 500ml aerosol | 22 liter canister |
| White | SI-646-0000-500 | SI-646-0000-022 |
Pallet unit:
500ml – 1,848 pieces
22L – 36 pieces
A spray gun is required to process this pressurised product.
SI-XXX-XXXX-XXX = Item number.